Ceramic tiles into Saudi Arabia — the quality mark is the factory's, not the shipment's.
Tiles look like a standard SABER job: product certificate, shipment certificate, done. They are not. Since 13 September 2019 ceramic and porcelain tiles have sat under the Building Materials technical regulation with a mandatory Saudi Quality Mark — a licence issued to a production line and a brand after a factory audit. Buyers who discover this at the loading port have usually already paid for the goods.
Short answer: yes, ceramic and porcelain tiles need SABER — a PCoC per model and an SCoC per consignment — and they need the Saudi Quality Mark (SQM), which has been mandatory for tiles since 13 September 2019 under the Technical Regulation for Building Materials – Part 4 (bricks, tiles, ceramics, sanitary ware and related products). The SQM is not something the buyer applies for at shipment time: it is a licence held by the factory, valid three years, tied to a specific production line and brand, renewed through annual surveillance audits. Without it the goods do not enter Saudi ports, however complete the SABER file looks.
Three layers, not one
Most "SABER guide" content treats every building material as the same two-certificate exercise. For tiles the stack has three layers, and they fail independently.
| Layer | What it is | Who holds it | Validity |
|---|---|---|---|
| Technical regulation | Building Materials – Part 4: Bricks, Tiles, Ceramics, Sanitary Ware and Related Products; decides which standards and tests apply to your category | The rule itself — applies whether or not anyone has read it | Until revised; check the current version |
| Saudi Quality Mark (SQM) | Factory-level licence: document review plus factory audit of production quality control, filed through SASO's Jeem1 portal | The manufacturer, per production line and per brand | 3 years, with annual surveillance |
| SABER certificates | PCoC per model (product conformity) + SCoC per consignment (shipment conformity) | Issued to the Saudi importer's account by an approved body | PCoC 1 year; SCoC per shipment, valid 90 days |
Layer definitions checked against SASO's Quality Mark pages and the QMS-CR-14 ceramic tile licensing procedure on 17 November 2026 — see official sources. Whether your exact SKU falls inside Part 4 is decided by the certification body, not by this page.
The standards your test reports have to name
SASO's ceramic tile licensing procedure cites one classification standard and the ISO 10545 test series. If a factory's report does not name these, it was written for a different market — a European EN 14411 report is good evidence of capability and poor evidence of Saudi compliance.
| Reference | Covers | Why the buyer should care |
|---|---|---|
| SASO GSO ISO 13006 | Ceramic tiles — definitions, classification, characteristics and marking | Fixes the category your product belongs to; the category drives which tests and which marking apply |
| SASO ISO 10545-1 | Sampling and basis for acceptance | Decides how many pieces are pulled and what counts as a pass — the clause most factory "test reports" skip |
| SASO ISO 10545-2 | Dimensions and surface quality | Length, width, thickness, straightness, rectangularity, surface defects |
| SASO ISO 10545-3 | Water absorption, apparent porosity, bulk density | The single number that classifies the tile — and the one buyers most often take on trust |
| SASO ISO 10545-4 | Modulus of rupture and breaking strength | Floor tiles in commercial use fail here first |
| SASO ISO 10545-6 / -7 | Deep abrasion (unglazed) / surface abrasion (glazed) | Wear class claims on the box; glazed and unglazed are tested differently |
| SASO ISO 10545-9 / -12 | Thermal shock / frost resistance | Riyadh's diurnal swing and outdoor use; frost claims need -12 explicitly |
| SASO ISO 10545-16 | Small colour differences | The technical basis for a shade-difference complaint — without it, "same colour" is an opinion |
Reference list taken from the standards table in SASO's QMS-CR-14 (ceramic tile quality mark procedure, V6.00), checked 17 November 2026. The full series runs to 10545-16; which tests your category needs depends on the classification below and on the claims you make for the product.
The classification printed on the licence
SQM certificates describe the product by manufacturing method and water absorption group. This is the vocabulary the laboratory, the certification body and the factory audit all use — and it is why "porcelain, 600×600" is not a specification.
| Forming method | Group | Water absorption (Ev) | Common trade description |
|---|---|---|---|
| Extruded (A) | AIa | ≤ 0.5% | Fully vitrified |
| Extruded (A) | AIb | 0.5% < Ev ≤ 3% | Porcelain-type |
| Extruded (A) | AIIa-1 / AIIa-2 | 3% < Ev ≤ 6% | Dense ceramic |
| Extruded (A) | AIIb-1 / AIIb-2 | 6% < Ev ≤ 10% | Ceramic |
| Extruded (A) | AIII | > 10% | Porous / wall tile |
| Dry-pressed (B) | BIa | ≤ 0.5% | Porcelain — the default for large-format floors |
| Dry-pressed (B) | BIb | 0.5% < Ev ≤ 3% | Porcelain-type |
| Dry-pressed (B) | BIIa / BIIb | 3% < Ev ≤ 6% / 6% < Ev ≤ 10% | Ceramic |
| Dry-pressed (B) | BIII | > 10% | Glazed wall tile |
Group definitions reproduced from the product classification table in SASO QMS-CR-14, checked 17 November 2026. Two suppliers quoting "600×600 porcelain" can be in different groups, with different breaking strength and different price — ask for the group, not the adjective.
What the factory has to already hold
The SQM application file is the most useful due-diligence checklist we have found for tile factories, because none of it can be produced in a week. A factory that can hand over this list is a factory with a functioning quality system; a factory that offers to "arrange it" is telling you it does not.
- Industrial licence for the plant and a valid commercial registration of the establishment — the legal entity, not the trading name on the website.
- Test reports from a SASO-recognised laboratory or an ISO/IEC 17025 accredited one, with the accreditation certificate and scope attached. A report from a lab whose scope does not include the test is not a report.
- Instructions and labels in English and Arabic — installation manual where applicable, product marking labels, photographs of the actual marking.
- Quality management evidence: QMS manual, factory quality control plan, factory location map, organisational chart.
- Accreditation certificates the factory already holds (ISO 9001, ISO 14001, ISO 22000 where relevant) — supporting evidence, not a substitute.
Document list summarised from SGS's published SQM guidance for ceramic tile exporters (2024), checked 17 November 2026. Requirements are administered by the approved certification body handling the file; expect it to ask for more, not less.
Why "we have SABER" is not an answer
Three different things get called "having certification", and only one of them survives customs.
- A PCoC is not an SQM. The PCoC confirms a model's conformity; the SQM confirms the factory's production control. Tiles in the mandatory scope need the licence regardless of how clean the PCoC looks.
- Someone else's certificate is not your coverage. SQM licences name the establishment, the production line address, the product category and the brand. A trader forwarding a photo of a licensed factory's certificate is showing you a supplier, not a compliant product — unless your order actually comes off that line under that brand.
- A category is not a SKU. The licence covers defined groups. A 10 mm outdoor paver and a 7 mm wall tile from the same plant may not both sit inside the scope; the packing list has to match what was registered.
The cost picture, without invented numbers
Two things are worth separating: what the platform charges, and what the factory's licence status costs you.
| Situation | What you pay | What it means for the order |
|---|---|---|
| Factory holds a valid SQM covering your category and brand | SABER product and shipment certificates can be obtained free of charge; your cost is the testing gap, if any, and the certification body's handling | The cheapest and fastest route — and the reason to check the licence before negotiating price |
| Factory does not hold SQM | No certificate fee applies, because there is no certificate to buy | The shipment does not clear. This is not a cost problem, it is a supplier problem |
| Existing reports are for EN 14411 or an older standard revision | Re-testing against the SASO-referenced standards, $300–2,000 depending on the gaps | Real money, but small against a stopped container |
For reference on the SABER layer alone, the platform fees are SAR 500 per PCoC and SAR 350 per SCoC before VAT, with a certification body fee of roughly $250–500. Those numbers apply to building materials generally; for tiles the licence status is the bigger variable.
What to send the factory
Six lines, in writing, before the price is agreed:
- Do you hold a valid Saudi Quality Mark licence for this product group and this brand? Send the certificate number and the product description page.
- Which production line and address is the licence registered to — the same one that will make our order?
- Which SASO standards do your current reports cite, and what is the report date and laboratory accreditation number?
- What is the water absorption group of this SKU, measured — not declared?
- Can you supply the marking artwork in Arabic and English, and photographs of it applied to the product or packaging?
- If our brand is not on the licence, what does adding it involve, and who pays?
Answers to these six take a serious factory two days and a trading company considerably longer, which is itself the test.
Official sources
Regulatory scope and licence conditions change. These are the primary pages to read before committing — reachable on 17 November 2026, but re-read them at the time of ordering:
- SASO — Saudi Quality Mark — the mandatory product list, which names ceramic and porcelain tiles, and current licence statistics.
- SASO — QMS-CR-14: licence procedure for ceramic tile (PDF) — the standards table, product classification and certificate content requirements.
- SASO — board decision making the Quality Mark mandatory for ceramic producers — the origin of the requirement.
- SABER — importer product certificate service — PCoC scope, fields and platform fee.
- SABER — importer shipment certificate service — per-consignment documents, fee and validity.
- SGS — securing the Saudi Quality Mark for ceramic tile exports — application documents, licence validity, and the free SABER certificates for SQM holders.
Questions buyers ask us
Do ceramic tiles need SABER to enter Saudi Arabia?
+Yes — and SABER is only one layer. Tiles fall under Building Materials Part 4, and since 13 September 2019 the Saudi Quality Mark has been mandatory for them. So: SCoC per shipment, PCoC per model, and a valid SQM licence held by the factory covering that category and brand. A PCoC does not substitute for the licence.
Can a Chinese tile factory get the SQM?
+Yes. The scheme is open to manufacturers, distributors, importers and exporters, filed through the Jeem1 portal with documents in English and Arabic. The licence attaches to the production line and the brand — which is why a trader forwarding another factory's certificate is not offering you coverage.
Is a PCoC enough, or do I also need SQM?
+Both, and they are different instruments. The PCoC is a product conformity certificate for a model, valid one year. The SQM is a factory licence issued after document review and a factory audit, valid three years with annual surveillance. Tiles holding a valid SQM can obtain their SABER certificates free of charge.
What if my supplier has no SQM licence?
+The goods cannot enter Saudi ports or be sold in the market under that route. Options: move the order to a licensed factory, or have a licensed factory produce it — but confirm your brand is inside the licence scope, because the certificate is issued per brand and names the establishment and line.
How long does SQM take?
+It depends on how complete the factory's documentation already is and on audit scheduling, so distrust single numbers. What shortens it: an existing ISO 9001 system, current ISO 10545 reports from a recognised or 17025-accredited lab, bilingual manuals and labels, and prior audits by an approved body. A factory with none of these is not a two-week project.