SABER certification for building materials — before the container, not at the port.
Saudi customs will not clear an imported consignment without the right SABER documents: a shipment certificate for every consignment, and a product certificate for products covered by a technical regulation. Which route applies depends on the product's HS code, its technical regulation and its end use. The process is straightforward on paper; in practice it fails because the factory, the buyer and the certification body each assume someone else is doing it.
Short answer: SABER is Saudi Arabia's online conformity platform, operated by SASO. Every imported shipment needs a Shipment Certificate of Conformity (SCoC); products covered by a technical regulation additionally need a Product Certificate of Conformity (PCoC) per product model, valid one year — while products outside any technical regulation take a free importer self-declaration followed by the same SCoC. Building materials are squarely inside the scope — windows, insulation, waterproofing, tiles, sanitary ware, cables, panels and prefab components all require it. Some categories go further: ceramic and porcelain tiles, steel bars and plates, cement, ready-mix concrete and aluminium composite cladding panels also need the Saudi Quality Mark (SQM). The certificates are issued to the Saudi importer's account; the evidence — test reports, ISO certificates, factory data — comes from the Chinese manufacturer. Platform fees are SAR 500 per PCoC and SAR 350 per SCoC before VAT, plus certification-body fees of roughly $250–500 and testing where reports are missing; a first-time registration with testing takes two to four weeks.
Which route applies to your product
Before anything else, establish which of the three routes below the product falls into. Importers regularly pay for a product certificate they did not need, or skip one they did.
| Route | How to tell | Documents required |
|---|---|---|
| Regulated product | The product is named in, or clearly falls within, a SASO technical regulation (most building materials: windows and doors, insulation, waterproofing, tiles, sanitary ware, cables, panels, prefab components) | Product certificate (PCoC) per model, valid one year + shipment certificate (SCoC) per consignment |
| Non-regulated product | No applicable technical regulation covers the product | Free importer self-declaration on the platform + shipment certificate (SCoC). The SCoC is not waived. |
| Additional scheme | The product is also in SASO's mandatory Saudi Quality Mark (SQM) scope — ceramic and porcelain tiles, reinforcing steel and steel plates, cement, ready-mix concrete, aluminium composite cladding panels | The route above, plus a factory-level SQM licence. A PCoC does not substitute for it. |
Route definitions checked against SABER's importer pages and SASO's technical regulations on 17 November 2026 — see official sources. Product classification is ultimately decided by the certification body, not by this page.
Why building-material shipments get stuck
SABER failures are almost never technical — they are coordination failures. The patterns we see repeatedly:
- Discovered too late. The buyer learns about SABER when the container is already booked. Testing takes weeks; the shipment misses its vessel and storage charges start.
- The factory said "no problem." Many factories assume SABER is the buyer's job and say whatever ends the conversation. Ask for the specific documents — test reports against the applicable standard, ISO 9001, product data — not for reassurance.
- Wrong technical regulation. Each product family is certified against a specific SASO technical regulation or an accepted standard. Certifying insulation under a generic regulation, or using a test report from five years ago against a since-updated standard, gets the PCoC rejected.
- Model mismatch. The PCoC covers specific models, materials and ratings. If the shipment contains a model not on the certificate, customs stops it — even though the factory shipped "the same thing, different size."
The two certificates, in order
| Step | What it is | Who does it | Time & cost (typical building material) |
|---|---|---|---|
| 1. Test reports | Lab reports against the applicable SASO technical regulation or accepted standard | Factory, or a lab the buyer appoints | $300–2,000 if missing; 2–4 weeks |
| 2. Product certificate (PCoC) | Registered on SABER per product model, valid one year | SASO-approved certification body, on the importer's account | SAR 500 platform + $250–500 CB fee; 5–6 working days (official estimate) once reports are complete |
| 3. Shipment certificate (SCoC) | Issued per consignment against the PCoC | Certification body, after reviewing packing list & invoice | SAR 350 + CB fee; 1–2 working days (official estimate) |
| 4. Customs clearance | Both certificates verified on the platform | Saudi importer / customs broker | Same day if documents match |
The PCoC is the part worth planning for: it is annual, model-specific, and needs the factory's evidence. The SCoC is routine once the PCoC exists — budget one to two working days per shipment — certificates are valid 90 days — and make sure the packing list matches the certificate exactly.
When SABER is not the whole story: SQM and the 2026 labelling rule
Saudi Quality Mark (SQM). A PCoC does not satisfy every requirement on its own. SASO makes the Saudi Quality Mark mandatory for a set of higher-risk products, and several of them are core building-material categories: ceramic and porcelain tiles, reinforcing steel and steel plates, cement, ready-mix concrete, and aluminium composite panels used for cladding. SQM is a different exercise from a PCoC — the factory's production quality control is assessed, with an application through SASO's Jeem1 portal, document review, a factory audit, and a licence valid three years subject to annual surveillance audits. If your product falls in this list, ask whether the factory already holds the relevant SQM licence — discovering after production that it does not is an expensive surprise. The licence also changes the arithmetic: products covered by a valid SQM licence can obtain their SABER product and shipment certificates free of charge, so for tiles the certificate fee question is settled by the factory's licence status rather than by the certificate body.
On-product labelling from 1 October 2026. SASO's circular requires products covered by ten named technical regulations — including Building Materials Part 3 (hydraulic binders and related products) — to carry the supplier's name and commercial registration (CR) number on the product itself. The "supplier" here is the Saudi importer or the local manufacturer, not the Chinese factory: the details must come from your Saudi customer and match what is registered on SABER. Check the marking requirement before production, not just the outer packaging.
Official sources
Fees, timelines and validity periods change. These are the primary pages to check before you commit — verified reachable on 17 November 2026, but always re-read them at the time of ordering:
- SABER — importer product certificate (PCoC) service — scope, required fields, current platform fee.
- SABER — importer shipment certificate (SCoC) service — per-consignment documents, fee and validity.
- SABER — non-regulated products — the self-declaration route.
- SASO — technical regulations (building materials) — the regulation text that decides whether your product is regulated.
- SASO — Saudi Quality Mark — mandatory product scope, application route, licence validity.
What to ask the factory before you place the order
- Have you exported this product to Saudi Arabia under SABER? Ask which certification body was used and request a copy of an earlier PCoC. A factory that genuinely exports to Saudi has one.
- Which technical regulation applies to this model? Get the regulation number in writing. If the factory cannot name it, the test reports they hold probably do not cover it either.
- Are the test reports current? Reports older than the latest standard revision, or issued to a different model, are close to worthless for registration.
- Will you support re-testing if needed? Agree who pays before, not after — re-tests are cheap to agree on and expensive to argue about with a deposit down.
Where a sourcing agent fits in
Certification itself is done by SASO-approved bodies — an agent cannot issue certificates, and one that claims to be able to should be treated with caution. What an agent on the ground does is make the process non-failing: confirming the applicable regulation and evidence gaps before the order, chasing the factory for real reports rather than reassurance, checking that model numbers on the packing list match the PCoC, and sequencing testing so it runs parallel to production instead of after it. The saving is not the fee — it is the vessel you do not miss and the storage you do not pay.
Questions buyers ask us
What is a SABER certificate?
+SABER is Saudi Arabia's online conformity platform run by SASO. Regulated products need a PCoC per model plus an SCoC per shipment; non-regulated products take a free importer self-declaration plus the SCoC. Without the required documents, Saudi customs will not clear the goods.
Do building materials need SABER certification?
+Almost all of them do, but not all in the same way. Windows and doors, insulation, waterproofing membranes, tiles, sanitary ware, cables, panels and prefab components fall under SASO technical regulations and need a product certificate (PCoC) plus a shipment certificate (SCoC). Products outside any technical regulation take a self-declaration plus the SCoC. Tiles, steel, cement, ready-mix concrete and aluminium composite cladding also need the Saudi Quality Mark.
Who applies — the buyer or the Chinese factory?
+Certificates are issued against the Saudi importer's account; the test reports and factory documents come from the manufacturer. Factories exporting to Saudi regularly can support the process — many cannot, and the buyer discovers it late. Agree the document split before placing the order.
How much and how long?
+SAR 500 per PCoC and SAR 350 per SCoC before VAT, $250–500 per product certificate for the certification body, plus $300–2,000 in testing if existing reports are missing or outdated. Non-regulated products take a free self-declaration instead of a PCoC. First-time registration with testing: two to four weeks. The PCoC is annual; the SCoC is per shipment, one to two working days, valid 90 days.
Do all building materials need the Saudi Quality Mark (SQM)?
+No — only products in SASO's mandatory SQM scope: ceramic and porcelain tiles, reinforcing steel and steel plates, cement, ready-mix concrete, and aluminium composite cladding panels, among others. SQM requires factory-level assessment through SASO's Jeem1 portal, with a licence valid three years and annual surveillance audits. Confirm whether the factory holds the licence before placing the order.