Precision stainless tubing sourced at the mill
Seamless stainless tubes and pipes from OD 3.18 mm upward — fluid, heat-exchange and high-pressure boiler formats with AP pickled, BA bright and EP electropolished surface routes, capillary to large diameter, plus U-bent, precision-cut and special-shaped tubes. Quotations are built line by line against the exact standard, surface and tolerance your project specifies, with EN 10204 3.1 mill certificates checked before anything ships.
Nine product families
Stainless Steel Seamless Pipes
Seamless stainless steel pipes for fluid transport, heat-exchange and boiler-tube formats.
Seamless Heat-Exchange U-Tubes
U-bent austenitic stainless steel seamless tubes for heat-exchange equipment.
Large-Diameter Austenitic Stainless Pipes
Austenitic stainless steel pipes supplied in large-diameter form for headers, manifolds and heavy-duty lines.
AP Annealed & Pickled Tubes
Stainless tubing with an annealed-and-pickled surface finish — the economical route for chemical and utility lines.
BA Bright Annealed Stainless Tubes
Bright-annealed tubes with controlled dimensional and inner-surface references; the base stock for EP.
EP Electropolished Tubes
Tubes with an electropolished interior for high-purity, hygienic and CIP/SIP-cleanable circuits.
Precision Seamless Steel Tubes
Cold-drawn and cold-rolled tubes with controlled OD, ID and straightness for instrument and mechanical use.
Fine-Cut Short Tubes
Short tube sections cut to a stated length tolerance, deburred and chamfered where required.
Special-Shaped Steel Tubes
Square, hexagonal and other profiles made to a supplied cross-section or drawing.
Three surface routes
AP — Annealed & Pickled
Matte silver-white, Ra 0.8–1.6 μm. The most economical route; suits chemical fluid lines, water treatment and heat exchange — not high-purity or hygienic circuits.
Enquire →BA — Bright Annealed
Bright reflective finish with good cleanliness at moderate cost; the base material for EP tubes. Interior micro-peaks still hold trace particles.
Enquire →EP — Electropolished
Mirror-smooth interior with minimal particle adhesion and better corrosion resistance; CIP/SIP cleanable. Costs typically 30–80% above BA with lower capacity.
Enquire →Standards & verification
Dual-standard compliance
ASTM A312 / A213 (fluid and heat-exchange), A789 / A790 (duplex 2205, 2507, 254SMO), A106 Gr.B, A269; EN 10216-5 for pressure service; GB/T 14976, GB/T 3639, GB/T 8163. Grades from 304 and 316L to 904L and nickel alloys.
Certificates & NDT
EN 10204 3.1 mill test certificates checked against heat numbers before shipment. Eddy-current, ultrasonic and penetrant inspection available at the mill; spectrometer, tensile, impact and hardness testing on request.
Tolerance capability
Precision formats from 3×0.3 mm to 426×30 mm with OD tolerance to ±0.03 mm, ID ±0.05 mm, straightness 0.5/1000, and cut length tolerance ≤0.1 mm with chamfering.
Have a tubing specification? Send it over.
Send the tube form, material, dimensions, surface finish, standard and destination. We return the key questions, a sourcing view and an indicative cost range — usually within one business day.
Start a tubing enquiry →九大产品系列
不锈钢无缝管
涵盖流体输送、换热管及高压锅炉管等产品形式。
奥氏体不锈钢无缝 U 形换热管
用于换热设备的 U 形奥氏体不锈钢无缝管,弯曲半径与直段按图纸或工艺要求确定。
大口径奥氏体不锈钢管
以大口径形式供货的奥氏体不锈钢管,用于集箱、汇管与重载管线。
AP 退火酸洗管
采用退火与酸洗表面处理的不锈钢管,化工与公用工程管路的常规选择。
BA 不锈钢光亮退火管
光亮退火表面,尺寸精度与内表面粗糙度均有明确控制,可作为 EP 管的基材。
EP 电解抛光管
内壁经电解抛光,适用于高纯、卫生级及可 CIP/SIP 清洗的管路系统。
冷拔/冷轧精密无缝钢管
针对外径、内径与直线度有明确控制要求的精密无缝钢管,用于仪表与机械部件。
精切短管
切长公差明确的短管精切产品,可按要求去毛刺与倒角。
异形钢管
提供方管、六角管及按截面图纸定制的异形管形式。
三种表面路线
AP — 酸洗钝化
亚光银白色、磨砂质感,Ra 0.8–1.6 μm,成本最低。适合普通化工流体、水处理与换热管路,不适合高纯或卫生级场合。
BA — 光亮退火
亮银反光但非镜面,洁净度不错、价格适中,是 EP 管的基材;内壁微观峰谷仍会吸附微量颗粒。
EP — 电解抛光
内壁镜面效果,颗粒附着极少、不易析出、耐腐蚀更好,可 CIP/SIP 清洗无残留;成本一般比 BA 高 30%–80%,产能相对低。
标准与验证
双标准体系
美标 ASTM A312 / A213(流体与换热)、A789 / A790(双相钢 2205、2507、254SMO)、A106 Gr.B、A269;欧标 EN 10216-5 压力用无缝管;国标 GB/T 14976、GB/T 3639、GB/T 8163。牌号覆盖 304、316L 至 904L 与镍基合金。
证书与无损检测
出厂可提供 EN 10204 3.1 材质检验证书,出货前按炉号逐项核对。钢厂可执行涡流 ET、超声 UT、渗透 PT 无损检测;光谱成分分析、拉伸、冲击、硬度试验按需安排。
精度能力
精密管 3×0.3 mm 至 426×30 mm;外径公差 ±0.03 mm、内径 ±0.05 mm,直线度 0.5/1000,精切短管长度公差 ≤0.1 mm,支持倒角加工。